Hot Work Permit Application
Home
Apply
Sign in
Wayne County Airport Authority – Hot Work Permit
Site Survey For: Cutting, Welding, Burning, AND/OR Tar Kettle Work at ALL DTW/YIP Locations.
Permits issued by Fire/Rescue DTW - 734.942.3603 | YIP – 734.485.6660
IN CASE OF EMERGENCY CALL 911
Survey Requested By
Contact Person
Contact Number
Contact Email
After Inspection This Will Permit
Location
To
Start Date & Time
End Date & Time
The operator shall take the necessary precaution to eliminate all possible fire hazards and to prevent damage to any construction work, building materials, equipment and all other property, both public and personal involved in connection with their work to be done. The provisions of the following shall apply at all times. If a portable WELDING CART is being utilized, then at least ONE PORTABLE EXTINGUISHER MUST be attached to the cart with a MINIMUM RATING of 2A-10BC. THESE ARE THE MINIMUM REQUIREMENTS. If it is determined that the hazard warrants additional extinguishers and/or other life safety precautions, then the permit holder will be REQUIRED to meet all the conditions before beginning their operations.
BY ORDER OF THE AIRPORT FIRE MARSHAL
THE FOLLOWING CONDITIONS SHALL BE INSPECTED PRIOR TO APPROVAL
Working On Walls or Ceilings
Combustible Coverings shall NOT be used.
C
N/C
N/A
Combustibles shall be moved away, from the opposite side of the wall being worked on.
C
N/C
N/A
Covers suspended beneath work to collect sparks shall be non-combustible.
C
N/C
N/A
Work on Enclosed Equipment
The Equipment will be cleaned of all combustibles.
C
N/C
N/A
The container will be purged of all vapors and verified with a gas detection meter.
C
N/C
N/A
Equipment has been safely taken out of service and properly locked and tagged out.
C
N/C
N/A
Work in Enclosed Equipment (Confined Spaces)
Contractor shall properly ventilate the space and have a gas meter onsite full time to monitor the space. Contractor must have their own rescue equipment onsite and be Confined Space Entry Trained.
C
N/C
N/A
Fire Watch
No ignition source within 100 feet of aircraft.
C
N/C
N/A
Operator shall supply extinguishers of appropriate size and type. They shall be located not more than fifty (50) feet from the operations.
C
N/C
N/A
Operator shall be trained in use of extinguishing equipment and in sounding of fire alarm and notifications. It is the responsibility of the Company/Tenant to ensure that operating personnel have received such training.
C
N/C
N/A
Provided during operations, with FINAL inspections thirty (30) minutes after operations cease.
C
N/C
N/A
Within 35 feet of Work
Fixed site combustibles and flammable liquids shall be protected with covers, guards, or metal shields.
C
N/C
N/A
Combustible floors shall be wet down, covered with damp sand, metal or other shields.
C
N/C
N/A
Movable combustible materials and flammable liquids shall be relocated outside the work area.
C
N/C
N/A
The floors shall be swept clean of combustibles.
C
N/C
N/A
All wall and floor openings shall be covered.
C
N/C
N/A
Tar Kettle Operations
A minimum of two (2) portable extinguishers with a minimum rating of 2A-20BC shall be maintained in a proper working order not closer than ten (10) feet nor more than fifty (50) feet from the TAR KETTLE operations area.
C
N/C
N/A
Propane fuel tanks shall be secured and maintained at all times. Also, all supply hoses and regulators shall be maintained in the appropriate manner (i.e. free of leaks, tears, cuts).
C
N/C
N/A
Miscellaneous
If working in a fuel farm or fueling station, verify that the contractor has a written Safety Plan.
C
N/C
N/A
While working in ANY terminal, contractors must use a ventilator or smoke eater to remove the welding hot work fumes.
C
N/C
N/A
AT THE TIME OF THE SURVEY THE ABOVE CONDITIONS WERE FOUND. ANY NON-COMPLAINT ITEMS SHALL BE CORRECTED BEFORE OPERATIONS BEGIN
Close
